MetecnoPanel®PIR Insulated Wall Panel

MetecnoPanel® is an insulated wall panel with a PIR fire-retardant core delivering exceptional thermal performance and made exclusively with a BlueScope® steel to suit Australia’s harsh conditions. MetecnoPanel® is GreenRate certified and FM approved to FM 4880 & 4881 – No Height Restriction and is suitable for all insulated panel applications, from cold storage to exterior warehouse walling. Servicing the commercial and industrial market segments, MetecnoPanel® is used as a alternative to concrete tilt panel and traditional claddings to deliver a thermally efficient, attractive and hard wearing pre-painted finish in traditional COLORBOND® colour palette.

MetecnoPanel® offers FM Global insurer approved fire risk reduction properties, widely specified in Europe and USA.

Advantages

  • High Thermal Performance for Section J compliance
  • FM Approved
  • GreenRate certified
  • Australian Made

Typical Applications

  • Coolrooms & Freezers
  • Health & Infrastructure
  • Ceilings, Walls and Partitions
  • Office Fit-Outs & Retail Applications
  • Laboratory & Clean Room Walls & Ceilings
  • Internal Partition Walls
  • Transportable Buildings
  • Factories
  • Education and Government Buildings
  • Entertainment and Convention Centres

Equitilt FlameGuard® Non-Combustible Cladding & Fire Rated Walls

Equitilt FlameGuard® is a non-combustible and fire-rated walling product with a non-ozone depleting Mineral Wool core, encased in BlueScope® steel pre-finished in COLORBOND® .

Equitilt FlameGuard® has been tested & certified to achieve up to a 3 Hour Fire Rating, also offering a range of cost-effective Equitilt FlameGuard® wall configurations that can achieve project specific FRL requirements of  -/60/60, -/90/90 or -/120/120 in addition to the -/180/180 (3 hours).

The Equitilt FlameGuard® wall system not only has high thermal performance & energy efficiency but is fire-resistant walling panel made from pre-finished Australian-made Bluescope® COLORBOND®  steel and is well suited to long spanning applications which require Non-Combustibility, FRL or FM Approval for insurance purposes. Equitilt FlameGuard® 50mm & 75mm are FM Approved to FM 4880 No Height Restriction. Equitilt FlameGuard® Plus 100mm & 150mm are FM Approved to FM 4880 & FM 4881 No Height Restriction and is recommended where improved fire performance is required for insurance purposes in walling and ceiling applications.

To learn the correct method for handling and installing MW core panels click here to view.

Note: Please check COLORBOND® colour availability with your local Bondor representative prior to specification as project min order quantities may apply.

Advantages

  • Fire Rated walling product
  • Certified to achieve up to a 3-hour fire rating
  • Non-Ozone Depleting MW core
  • Cost effective
  • Suited for long spanning applications which require Non-Combustibility, FRL or FM Approval for insurance purposes

Typical Applications

  • Architectural
  • Sustainable Buildings
  • Retail and Showroom Premises
  • Walls and Partitions
  • Insulated Walling
  • Warehouses

BondorPanel® Coldroom Panel

BondorPanel® is purpose designed for cold storage, controlled environments and general wall construction as a lightweight, high performing EPS-FR insulated walling and ceiling panel manufactured exclusively using Australian-made BlueScope COLORBOND® Intramax™ steel specifically used to protect and temperature control cold storage, cool rooms, food handling, laboratory and clean room facilities.

BondorPanel® with COLORBOND® Intramax™ steel contains a unique antibacterial technology that actively helps reduce the risk of cross-contamination and inhibits growth of surface bacteria that may cause potential odours, stains, food poisoning and allergies. Complying fully with FDA, EUSCF, and local standards by specifying BondorPanel® with COLORBOND® Intramax™ steel will you ensure your hygiene sensitive areas receive the ultimate in antibacterial protection.

BondorPanel® is made to measure, then assembled on-site. Easy handling and quick, simple installation keep construction time to a minimum. BondorPanel® EPS-FR panel is ideal for a range of applications, from long spanning cold storage facilities to clean rooms, portable cold storage containers and transportable buildings.

Advantages

  • Versatile application
  • High thermal efficiency
  • Lightweight
  • Made with COLORBOND® Intramax™ steel that contains antibacterial technology
  • Assembled on site
  • Made to measure

Typical Applications

  • Coolrooms & Freezers
  • Health & Infrastructure
  • Ceilings, Walls and Partitions
  • Office Fit-Outs & Retail Applications
  • Laboratory & Clean Room Walls & Ceilings
  • Internal Partition Walls
  • Transportable Buildings

MetecnoSpan®PIR Roofing

MetecnoSpan® PIR insulated roof panels deliver a Section J conforming roof and insulation system with the highest thermal performance using a fire-retardant PIR core continuously formed and expanded between layers of BlueScope® COLORBOND® steel, manufactured to AS1397 standards.

MetecnoSpan® conforms to NCC and insurer requirements with a roofing solution that is Australian Standards tested, CodeMark™ accredited, GreenRate certified and FM Approved to FM 4880 (No Height Restriction) and FM 4471 (External Wall and Roof Endurance Standard).

Advantages

  • Meets Section J Thermal Requirements
  • Longest PIR roof runs in Australia
  • Low Pitch and compatible with SecureLap® system to eliminate the reliance on sealants and butyl tape
  • Made in Australia for Australian Conditions

Project Applications

  • Retail & Shopping Centre Roofs
  • Commercial
  • Agricultural
  • Warehouses
  • Industrial
  • Any owners requiring FM Approval and FM Global Insurer approved roofing systems

SolarSpan® Insulated Roof Panel

SolarSpan® is Australia’s leading insulated roofing panel offering long-spans, low pitch and high thermal efficiency to satisfy Section J requirements in commercial, industrial and residential applications. Developed over 20 years ago this engineered all-in-one insulated roofing solution offers a ceiling, insulation and roof sheet in one product for optimal thermal and build efficiency when constructing high performance building envelopes. CodeMark™ approved and Australian Standards tested SolarSpan® features a COLORBOND® steel exteriorroof layer, an EPS-FR rigid insulation core with a pre-finished COLORBOND® ceiling underside,

SolarSpan® insulated roofing is faster to install than conventional roofing, eliminates the need for additional structural supports and extra layers as required in traditional roofing system eliminating purlins, beams, trusses, mesh, sarking, insulation and plasterboard as well as reducing the need for mutliple trades onsite.

Advantages

  • Meets Section J Thermal Requirements
  • Faster to install than traditional roofing methods
  • Long Spans
  • Low Pitch and compatible with superior end lap SolarLap® system
  • Made in Australia for Australian Conditions, tried and tested in Cyclonic regions
  • Compatible with SolarLap® superior End Lap system to eliminate reliance on sealants and butyl tape

Project Applications

  • Retail & Shopping Centre Roofs
  • Commercial
  • Educational Facilities – gymnasiums, assembly areas, auditoriums and classrooms
  • Warehouses
  • Residential House Roofs
  • Shaded structures and awnings

InsulRoof® Next Gen Corro Roof

The next generation in Australian residential roofing has been realised with InsulRoof®, the steel insulated roofing panel featuring contoured COLORBOND® roof lines and dual layers of high performance SupaCore® insulation. InsulRoof® is the inspired roofing solution, delivering Australian homes the ultimate in thermal and aesthetic benefits.

InsulRoof® features a corrugated COLORBOND® steel exterior, a lightweight expanded polystyrene core with fire-retardant (EPS-FR) for high performing insulation, and a pre-painted COLORBOND® steel underside. These high strength panels allow for impressive spans and are faster to install, eliminating the need for traditional trusses, mesh, sarking, insulation, plasterboard and supporting trades. Available nationwide with a 20 year manufacturer’s warranty and up to 25 year COLORBOND® steel warranty, InsulRoof® is the inspired solution for Australian homes.

Advantages

  • Long Span
  • Low maintenance
  • Easy installation eliminating the need for trusses, mesh, sarking, insulation and plasterboard
  • Cost Effective
  • High performing dual layer SupaCore® insulation

Typical Applications

  • Carports & Patios
  • Gazebos
  • Multi and Singular Residential Roofs
  • Insulated Roofing
  • Modular & Sustainable Buildings
  • Commercial and Industrial Roofs

Equideck® Flat Roofing

Equideck® Flat Roofing is a standing seam like profile with long-spanning structural performance, suitable for achieving a streamlined and minimalist architectural roof profile. Equideck® offers three features in each panel including a durable BlueScope® COLORBOND® steel roof, a high performing insulation core (EPS-FR) and an attractive, low-maintenance pre-painted BlueScope® COLORBOND® ceiling. Equideck® roofing is available in a modern COLORBOND® colour palette delivering a unique profile to designers.

Advantages

  • Long Span
  • Streamlined and minimalists
  • Low maintenance
  • Easy installation
  • Cost Effective
  • High performing insulation core

Typical Applications

  • Covered Walkways
  • Education & Government
  • Insulated Roofing
  • Retail and Showrooms
  • Sustainable Buildings
  • Wineries

EconoClad®PIR Roofing

EconoClad® PIR Insulated roofing is a low-cost PIR roofing solution made with a COLORBOND® steel roof, PIR core (Polyisocyanurate) and foil or vinyl ceiling underside. EconoClad® easily satifyies Section J requirements with a range of thickness options delivering R-Values up to R4.55.

EconoClad® delivers on tight budgets and project timelines across industrial, commercial and agricultural roof and wall cladding applications. EconoClad® as an economical and practical roof or wall cladding solution that  is faster to install than bulk-insulation and grid systems, eliminating multiple roofing layers with a single high performance roofing material.

Advantage

  • Economical
  • Practical roof or walling solutions
  • Faster to install
  • Alternative to bulk insulation and roof insulation systems
  • Offers high performance roofing material
  • Satisfies Section J requirements

Project Applications

  • Perfect for Asbestos roof replacements
  • Warehouse roofing
  • Shed Roofing
  • Chicken Shed
  • Storage Facilities
  • Industrial Shed Roofing
  • Agricultural Roofing

MetecnoInspire®PIR Secret-Fix Wall Panel

MetecnoInspire® is an insulated architectural façade wall system delivering a high end appearance with a pallete of inspiring colours and attractive surface profiles. MetecnoInspire® architectural panels are available in thicknesses 50mm, 60mm, 80mm and 100mm providing excellent thermal performance and custom lengths up to 16m.

MetecnoInspire® has a unique hidden-fix system concealing fasteners from sight, creating a flush and aesthetically pleasing finish for use in a variety of applications including external façades, internal walling and partition walls.  MetecnoInspire® has a rigid foam PIR core between two skins of COLORBOND® steel forming an exeptionally strong, durable and fire-retardant walling panel.

Advantages

  • Versatile
  • Available in standard & metallic COLORBOND® colours
  • Available in 6 attractive surface profiles
  • Offers designers an attractive finish without compromising structural integrity and thermal efficiency
  • 25% more efficient as an insulation medium compared to pre-cast concrete of equivalent thickness
  • Lightweight allowing reduced load- bearing footings and structural supports

Typical Applications

  • Architectural
  • Education & Government
  • Exhibitions & Convention Centre’s
  • Retail and Showrooms
  • Sustainable Buildings
  • Sport & Cultural Buildings
  • Walls and Partitions
  • Warehouses